Almost all electronic gadgets and devices have printed circuit boards as part of the components that constitute them. Manufacturing of PCB is not a difficult process and even amateur electricians can just provide the manufacturer with their own designs in order to get it done. The boards are divided into three categories; multi layer, single and double side boards. Conduction of these boards is usually done using copper, nickel or aluminum based material. The material is chosen depending on how complex or dense the circuits are. Described here is the process followed when going about creating them and the stages involved.
A conductive material is used to plate the backing. Conduction between the layers is enhanced by drilling holes into the backing. To remove any small conductor particles that may be present, the board is scrubbed. Filtration process is applied to recycle the recovered particles. This is because, if not recycled, the copper may form a mixture with the other wastes and then become quite hazardous to the environment.
Cleaning of the board is then done. In the next stage, there should be adequate adhesion and therefore to enhance this, etching is also done. One more layer of conductor is added next. The holes that had been drilled earlier should be conducted; hence the application of electrolysis copper plating is vital. Acidic based solutions and alkaline ones are used so that the pH is properly balanced.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Obtaining alternative resist can be achieved by use of other compounds that are photosensitive or organic. They can be used in their dry or wet forms. When exposed to ultraviolet light, they become hard.
In order to spread the liquid resist, one can use a silk screen, squeegee, roller or spray. One or both sides can have the liquid on. However, application can also be done to a specific area on the surface. Finer circuits can be produced by use of light.
The formation of multi layer panels is the final stage of this process. The inner cores of the layer are put together. The panels that are assembled together look like a copper foiled book with alternating epoxy sheets.
High heat and pressure are applied to the book which is placed in a lamination press. A bond will be formed as the epoxy layers are melted down by the intense heat and pressure. Holes are drilled into it. However, this should only be done after it has been trimmed and buffed as required. The desired results can only be achieved by following the required procedure well and adhering to each and every detail in the stages involved in manufacturing of PCB.
A conductive material is used to plate the backing. Conduction between the layers is enhanced by drilling holes into the backing. To remove any small conductor particles that may be present, the board is scrubbed. Filtration process is applied to recycle the recovered particles. This is because, if not recycled, the copper may form a mixture with the other wastes and then become quite hazardous to the environment.
Cleaning of the board is then done. In the next stage, there should be adequate adhesion and therefore to enhance this, etching is also done. One more layer of conductor is added next. The holes that had been drilled earlier should be conducted; hence the application of electrolysis copper plating is vital. Acidic based solutions and alkaline ones are used so that the pH is properly balanced.
The circuit's final design is arrived at with the use of photo imaging. Electroplating copper also helps in arriving at the final required thickness. Application of a thin layer of tin or lead solder takes place to allow for the protection of the final circuits. Removal of the unwanted copper is done as it will not be part of the final circuit. Its etching can be carried out using an acidic or alkaline solution.
Obtaining alternative resist can be achieved by use of other compounds that are photosensitive or organic. They can be used in their dry or wet forms. When exposed to ultraviolet light, they become hard.
In order to spread the liquid resist, one can use a silk screen, squeegee, roller or spray. One or both sides can have the liquid on. However, application can also be done to a specific area on the surface. Finer circuits can be produced by use of light.
The formation of multi layer panels is the final stage of this process. The inner cores of the layer are put together. The panels that are assembled together look like a copper foiled book with alternating epoxy sheets.
High heat and pressure are applied to the book which is placed in a lamination press. A bond will be formed as the epoxy layers are melted down by the intense heat and pressure. Holes are drilled into it. However, this should only be done after it has been trimmed and buffed as required. The desired results can only be achieved by following the required procedure well and adhering to each and every detail in the stages involved in manufacturing of PCB.
About the Author:
When you need to find reliable manufacturing of PCB, visit the web pages at www.becman.com today. You can see details online at http://www.becman.com now.
No comments:
Post a Comment